Streetglo Installing decals and stickers video and information.Help files hints and tips for stickers and decals installation.You can use any of these systems and suggestions to install your decals.The most important aspect of decal installation is whatever works for you is your best method.Just because we say to do it one way.RULES NOT TO BREAK Clean your hands The oils in your skin and even dead flakes of skin are easily picked up by the decal adhesive backing.Clean your hands completely and they will not cause harm to the sticky side of tthe decal.Clean your helmet, motorcycle, truck, boat or whatever completely Anything that is allowed to remain under the decal will cause a pipmple or blister that can not be repaired.A clean looking vehicle is not a clean vehicle.There is some degree of road film on it.There are pimple and blister contaminants on it that you can not see.After a good washing, wipe your bare hand across the newly cleaned area to feel for a completely smooth finish.FREE SHIPPING Perfect Replacement.Has your stock Mach 1 Hood Decal seen better days Well AmericanMuscle now offers a replacement White Mach 1 Hood Decal for.You can use any of these systems and suggestions to install your decals.The most important aspect of decal installation is whatever works for you is your best method.Need vinyl boat graphics Lettering on the Cheap is the place people go to buy Custom Boat Decals and to design Boat Name Decals.Shop todayYou can install very large decals with ease.However, on curved surfaces, such as helmets and sharply curved fuel tanks, Consider staying under 1.The exception to this is very long and narrow decals or pinstripereflecive tape, or FREEHAND decals that include our Mega.Flame, Classic flame, Tribal flames, and Speed.Stripes. These decals are applied always wet and are worked into place gradually.Keep in mind. A decal is flat.When you install a decal on a curved object, you are actually stretching the decal but not in direct terms never stretch decals, especially reflective ones.Here Are some general decal installation hints and tips 1.Mishandling. The decal material folds onto itself making the decal stick to itself and likely destroying the decal.Or, the decal is handled with dirty or oily hands inappropriately thereby reducing the adhesive problems.Blisters, Warts Pimples and Folds.Blisters are caused by getting a pocket of air under the material and are compounded by pressing on the bubble rather than removing the air.Warts and Pimples are caused by contaminants such as cloth, lint or a spec of dirt or sand getting onto the adhesive side of the decal.Folds happen when you apply over an irregular surface such as a round helmet, flared fender or motorcycle gas tank.Folds often result when trying to bend a decal around an irregular object.Chevy Cruze Vinyl Graphics and Decals Package Professional Style 3M Vinyl Graphics Kit PreCut and Designed, Ready to Install For Automotive Restylers.Peeling Edges Peeling edges happen when you have handled the tip of the decal so substantially that the adhesive has broken down and will not longer hold or bond.This problem also happens when you didnt clean the road film and contaminants from the vehicle or object.If it looks clean, wash the object anyhow One outing on a motorcycle for just a few hours will cause a road film to cover every object on your motorcycle or car. . Stretching Distortions.This happens from repeated removal and retry of the same decal or branch of a flame decal over and over again.Stretching distortions can cause a decal to crack or break loose from its bonding agent in just a few short days or weeks.Install-Boat-Name-Lettering-and-Decals-Step-2.jpg/aid6577-v4-728px-Install-Boat-Name-Lettering-and-Decals-Step-2.jpg' alt='How To Install Decal Works Graphics' title='How To Install Decal Works Graphics' />We will start by teaching you a few procedures and showing you a few fixes to complete your installation process.First, and most important, wash your hands Remove all body oil with a good hand washing.Body oil is a primary cause of decals that peel.Also, clean the surface of your project with soap and water.Eliminate every possible trace of road grime, dirt, oils or other contaminants.Motorcycle Helmets should be wiped with a cleaning solution as well.Just one 12 hour ride will put a road film on your helmet that will ruin the durability of the decal application.Prepare the work area Any contaminant that touches the adhesive side of your decal will stay there and ruin the appearance.And most importantly, take your time, dont rush the installationPlease note Since our customers include a large percentage of Motorcyclists, we design our reflective helmet decals to be helmet friendly.A case in point, we designed our Winged Skull to be cut into 3 sections for helmet installation.Vinyl will bend around a surface, but there is a limit to how much it can bend.Especially Reflective Vinyl which is a different formula from ordinary vinyl.Reflective Vinyl is easily damaged causing cracking and peeling.After preparing all surfaces, dry everything and do a trial application with the backing still on the decal.This is especially important for helmet and motorcycle applications.This will give you an idea where the Folds are going to naturally occur.Position the decal in place and try and hold it against the surface.If the surface is irregular round or shaped you must determine if application is possible all helmet decals sold by Street.Glo are helmet friendly.In some extreme cases you may have to pick a less curved location if the decal does not seem to be conformable to the shape of the item.Fitting a flat decal to a round object is a combination of choosing the first stick path, then slightly bending any branches off the main path around the object.In the case of flame decals, cut the backing of the decal so that you can apply the main flame body first, then apply each flame extension afterwards slightly pulling the flame in the lay down direction necessary to prevent folds.If you have a large multi component decal such as our winged skull, it will be much easier to cut the decal into sections and apply them in different steps.Our flame designs can be applied to nearly all Helmets and Gas Tanks if you follow the procedures herein Our winged skull is better applied in a cut format see link below.At a recent bike week attraction we passed out our smallest reflective skull decal measuring only 1.The large majority of bikers had no problem installing this tiny decal.However, the larger the decal, the more effort to get the flat object to bend around the irregular object.At the bottom of this document, if you see a link for a specific product, click it.There is more information and possibly even photos.IMPORTANT DECAL INSTALLATION Tips and Hints If you follow these procedures you should be able to install just about any decal from 1 to 2.You will need to decide between wet decal installation and dry decal installation.For our helmet flames, we recommend wet application even for decal installation experts.Here are the procedures 1.Clean your hands and the application surface thoroughly Make a solution of 1 cup pure water and 2 3 drops of Palmolive liquid dish washing detergent.You want a mixture that will cause water to evenly spread over a surface like a film and not like a freshly waxed surface like when your car is freshly waxed.If you remove all wax from the application surface, you can use plain water alone.Hold up the decal to the surface and mark its position with a reference tape such as masking tape.Decide on position now and not while handling the decal.Usually two markers applied will guide you during installation.When installing, you will be aligning the decal to the reference points pre determined before you actually install the decal.Apply the solution evenly to the object to receive the decal.Make sure the object is fully wet and saturated.Remove the decal from the backing fully for small objects or partially only for large objects.If you are working with helmet flames or stripes, remove only the first decal component you will be installing and place lightly on the wet surface and carefully prevent the decal from folding upon itself or tangling.Wet the adhesive side of the decal with the solution and carefully put it in place against your pre marked locations.It is ok for the decal to be sloppy at this point.You are only laying the decal on the object at this point, nothing more.Once you have the position you want start at the broadest end point of the decal and using your fingers as a squeegee, begin to push the solution out from under the decal.Work your way down the most center point of the decal until you reach the longest end.As you apply the decal, you might notice the beginning of a fold or roll just ahead of your pressure point.In this case, lift the unstuck portion of the deal and tug slightly to clear the fold or roll.In the case of flames install along the main flame centerline and leave all branches of the flame unapplied.Once the main flame body is applied, only then lift each extension and tug outwards as you work your way up the flame extension.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. Archives
November 2017
Categories |